Do you want to make a balloon costume? Are you willing to make a balloon stand for your party? And you're wondering how to go about it. If yes, then this DIY balloon costume stand is the answer to your questions.
You don't have to worry again; check out the guides below and learn how you can make a balloon costume stand by yourself.
Table of Contents
1. How To Make A Balloon Costume Stand
Find a way of making a balloon costume stand with an adorable two-tone balloon spiral and one top piece. It is straightforward to set up and cheap. Make the base of the stand with ¾" plywood.
Cut the plywood to 12'*12" pieces and paint it with white spray paint. Locate the center of the plywood piece and mark it with a pencil. Place a PVC flange on the center and mark the holes where the screws will be. Once you're done with the base, you have a way there.
2. How To Make A Cheap Balloon Stand
Making a balloon stand from foam board and some materials you have at home is very cheap. Get a white foam board and around & flat plate. Use the plate to draw out circles on the foam board.
Then use sharp scissors to cut out the circles. Now, you have four pieces of rings. Mashup the four fragments of the circle together to get one thick process for the base. You will need a champagne cup to hold the balloon yardsticks, which will keep the balloon.
3 Ways To Make Balloon Stand
Here are three straightforward ways of making a balloon stand. The first balloon stand is a PVC stand and here are the materials required for the building; PVC pipe, 4 ½" 90-degree elbow, ½" PVC Tee connector, PVC primer, glue, and PVC cutter (you can use a regular hand saw if you don't have a PVC cutter.
Start by making the square base for the stand; once the bottom is done, make sure there is one Tee connector facing up at the center of the floor, this is where the stand will fit into.
4. DIY Spiral Pattern Balloon Stand
Do you have a party and you don't want to spend so much money on decoration? Or maybe it's your daughter's birthday party, and you fill balloons, which would not be a bad idea for the occasion.
If you answer yes to the above question, then this is the best option for you. You can make this balloon stand from a cheap store-bought balloon stand kit. It is straightforward to put together, blow the balloons, hang them on the kit's balloon hanger, and assemble the stand.
5. DIY LLama Balloon Costume
See this super cute Llama balloon costume! It will look adorable on your daughter. The only color used for the balloon costume is white, and it is beautiful like that.
6. DIY Balloon Stand
For this balloon stand, we are mixing Colors like hot pink, sunshine yellow, green apple, blue turquoise, metallic pink, and pearl white! What a nice combo. The materials needed include a cutting board, rotary cutter, balloon sticks, balloons, scotch color, and pattern duct tape.
7. DIY Halloween Silhouette Balloon
Halloween is a season of fun and excitement. Everyone loves Halloween! Make this balloon costume in preparation for Halloween. It is straightforward and requires few materials. The materials include a balloon, yarn, and helium.
8. How To Make a Grape Punch Costume
See this adorable grape costume made from balloons. Since the color of the grape is purple, you need lots of purple balloons and a green strip of cloth to complete the grape costume.
9. DIY Balloon Centerpiece Stand
Learn how to make a balloon centerpiece by watching this 5 min video that explains the process from scratch.
The first thing you need to do is gather all the following materials; gold wrap paper to cover the base, a balloon tower attached to the center of the board to hold the stand, foam board for the ground, and ribbon to decorate the frame. After gathering all these, the next thing is to assemble them, which this video can guide you on.
10. DIY Balloon Stand
Making a tripod stand for your balloon doesn't sound as hard as it seems. All you need to do is determine the size of the sand and gather all the materials. You do not need many materials for this tripod stand except four steel/metal rods (three of the same length and one longer than the rest).
The three with the same length, mark them at a [oint some inches down the top. Curry them at this point at 90 degrees. Now, assemble the three and use a rope to tie them together like a tripod stand. Stretch the legs properly to give a more desired angle. After that, connect the longer piece to the sides of the tripod stand, and your balloon stand is ready.
11. DIY Round Backdrop With Balloon Garland
Backdrops are meant for decoration at an event, but it makes more sense and looks more adorable when you add balloons to them. See here the simple way to set up your round backdrop and make the balloon garland attached to it.
The scene is an all-around white stand, and the ballon color is purple, violet, ash, and lilac. Use a balloon pump to blow the balloons because the balloons are too much for something you can blow with your mouth.
12. How To Make A Balloon Stand
The easiest and faster way to get a balloon stand is to buy the balloon stand kit. The kit is not too expensive, and it saves you time. If you have the balloon stand kits, all you have to do is place the base down and thread the stands in the holes on the center one after the other. Once all the sand is there, go ahead and start blowing your balloon; attach the balloons in groups of four to the stands altogether.
13. DIY Balloon Arch Without Stand
Yes! You can make your balloon stand without a real stand or arch. All you need to do is blow the balloons, tie them together in two and further attach each pair making four balloons to form a square. Gather all the squares and start connecting them on top of each other using a dark pink ribbon. To create the arch, you need assorted link balloons.
14. How To Make A Spiral Balloon Column
Have you used a balloon sizer before? It will help if you use it because they make your balloon uniform and adorable. In this video, the instructor used a balloon sizer to determine the size of the balloons in the spiral balloon columns. This gives the cue a more exciting highlight. Also, use an electric air pump to blow the balloons.
15. DIY Hot Air Balloon Costume
You don't need any skill set to try out this hot air balloon. It is straightforward to put together. All you need to do is find some pieces of wooden rings and stack them together with glue. Blow your balloon and link it to the rings with rope.
16. DIY Hot Air Balloon Costume
If you want something hilarious and real for Halloween, this hot air balloon is great for that. The base of the hot air balloon is made from a cardboard box, and you can wear it on the lower part of your body while the balloon is above your head.
17. Making A Balloon Costume
If this is your first time making a balloon dress, you should observe this video and see how it is made. The dress was made from only link balloons. Two balloons were used, pink and blue, and the dress was made in a grid pattern; see the link below for more details about the balloon costume.
18. DIY Balloon Costume
Making a fall guy with only a balloon is not very easy but is fun to try out. The first step you need to take is to size the balloons. After sizing, make a circle with some balloons and keep adding more balloons for the subsequent layer of the ring.
Once the ring reaches the length, you want. Wear it for yourself to widen the circumference of the circle. Now start sizing the balloons for the other features of the fall guy like legs and arms.
19. DIY Balloon Costume Stand
See here how to make a hot air balloon stand from a cardboard box, rope, and link balloons. Make the base of the balloon costume with the cardboard box and the cord connecting the bottom to the hot air balloons.
Conclusion
There you have it! Twenty adorable DIY balloon costumes and stands. Check them out and start work immediately. Feel free to contribute or ask questions regarding this article, using the comments section below. Thanks for stopping by.
Ask Me Anything